Gable buildings are simply the best  and that's a fact. The simplicity of our product design holds costs down and delivers a solid, durable building you can depend on. From industrial enclosures requiring wall- or ceiling-mounted equipment to classroom, office or rental applications, our flexible design lets you choose the interior finish system that fits your needs.

View Gable Building Technical Specifications

View Accessories
Wall
Interior Wall
Interior Roof
Exterior Roof

Gable Specification Drawings - General specifications for the product.

Gable Approval Drawings -Drawings sent to the customer to verify design and dimensions; also to verify the sales contract description of what we agreed to supply.

Gable Erection/Final Drawings -Drawings showing floor plan, base channel with anchor bolt locations, elevations and roof plan used with details and installation instruction for building construction.

Single-Sloped Roof

Single Slope Building
Type S

Roof Design
Each "Type S" building shall have a single sloped (shed) roof with a pitch of 1 1/2"over the building width. The 16" wide interlocking roof panels shall vary from a nominal 24 to 18 gauge depending upon the loading conditions. They shall be attached to the wall cap through factory punched holes with #14 corrosion resistant fasteners.

The roof system shall include a gutter and a 2" X 3" downspout system at low sidewall, matching eave trim high side, and matching rake trim at the building endwalls. All gutters and trim shall be nominal 26 gauge galvanized steel pre-painted Arctic White or Roman Bronze.

Wall Design
The roof system is supported by a fluted, nominal 24 gauge, embossed, factory painted, 16" wide X 3" deep interlocking wall panel. The panels are fastened at the top and bottom to galvanized structural channels and wall caps with 3/8" diameter electrogalvanized machine bolts, through factory punched holes.

Structural Framing
Transmission of horizontal wind loads across the building shall be made through the roof panel system and no separate roof or wall diagonal bracing shall be required.

Where required for proper transmission of lateral wind loads, structural frame wind bents shall be installed. Wind bents shall consist of a prime painted column and rafter bolted assembly of steel conforming to ASTM A 36 specifications.

View Single Slope Building Technical Specifications

View Accessories
Wall
Interior Wall
Interior Roof
Exterior Roof

Single Slope Building Specification Drawings - General specifications for the product.

Single Slope Building Approval Drawings -Drawings sent to the customer to verify design and dimensions; also to verify the sales contract description of what we agreed to supply.

Single Slope Building Erection/Final Drawings -Drawings showing floor plan, base channel with anchor bolt locations, elevations and roof plan used with details and installation instruction for building construction.

Roof Design
Each building roof shall have 1 1/2" pitch in building width. Roof panels shall be interlocking and attached to the wall cap through factory punched holes with #14 corrosion resistant fasteners.

The roof system shall include a gutter and downspout system at low sidewall and matching rake trim at the building endwalls. All gutters and trim shall be nominal 26 gauge galvanized steel pre-painted Arctic White or Roman Bronze.

Wall Design
The roof system is supported by a fluted, nominal 24 gauge, embossed, factory painted, 16" wide X 3" deep interlocking wall panel. The panels are fastened at the top and bottom to galvanized structural channels and wall caps with 3/8" diameter electrogalvanized machine bolts, through factory punched holes.

Structural Framing
Transmission of horizontal wind loads across the building shall be made through the panel roof system and no separate roof or wall diagonal bracing shall be required.

Structural support and attachment of roof at existing building shall be the responsibility of others. In snow prone areas, drifting should be considered.

View Lean-To Building Technical Specifications

View Accessories
Wall
Interior Wall
Interior Roof
Exterior Roof

Lean-To Building Specification Drawings - General specifications for the product.

Lean-To Building Approval Drawings -Drawings sent to the customer to verify design and dimensions; also to verify the sales contract description of what we agreed to supply.

Lean-To Building Erection/Final Drawings -Drawings showing floor plan, base channel with anchor bolt locations, elevations and roof plan used with details and installation instruction for building construction.

The covered walkway/canopy system can be supplied in to distinctive designs. Firts is a system in which the structural framing is below the panels, the second system framing is above.

The panel support framing will be a nominal 14 or 12 gauge cold formed galvanized members or hot rolled prime painted members, as required with prime painted structural tube columns.

Panels shall be a maximum 16" wide with interlocking side ribs. The interlocking ribs shall be a minimum 3" high and turned upward.

Canopy Panels.
Canopy panels, fluted or flush, shall be a nominal 24 gauge galvanized coating confirming to G90 standards. Minimum yield strength of panel material shall be 50,000 psi for flus panels and 50,000 psi for fluted panels. The finish surface of the panel shall receive factory, roller applied, paint coats having a combined coating thickness of 0.8 to 0.12 mils od dry film thickness of white siliconized polyester formulation. Flush panels are also available in zinc/aluminum coated steel.

Attachment
Depending on design, top mounted panels shall be secured to the supporting structure with corrosion resistant fasteners with weather-tight washers where exposed to the elements. Underhung panels are attached with 3/8" corrosion resistant nuts and bolts.

View Canopy Technical Specifications

View Accessories

Canopy Specification Drawings - General specifications for the product.

Factory Assembled buildings are simply the best  and that's a fact. The simplicity of our product design holds costs down and delivers a solid, durable building you can depend on. From industrial enclosures requiring wall- or ceiling-mounted equipment to classroom, office or rental applications, our flexible design lets you choose the interior finish system that fits your needs.